Altronix NetWay8 Installation Instructions Uživatelský manuál stáhnout pdf (Strana 2)

- 2 - NetWay8/NetWay16

Overview:

Altronix NetWay8/NetWay16 Midspans provide power and pass data for PoE compliant cameras/edge devices. Cameras/

edge devices may be located up to 100m (328 ft.) from the NetWay unit. A NetWayXT repeater module can be utilized to

extend the distance an additional 100m (328 ft.) for a total range of up to 200m (656 ft.). A maximum range of

600m (1968 ft.) is possible using multiple repeaters, based on camera/device port requirement. NetWay Midspans are

capable of supporting non-PoE compliant fixed and PTZ IP cameras utilizing NetWay1512 or NetWay3012 adapters.

NetWay Specifications:

NetWay8:

•Eight(8)portsofcameras/edgedevicesoverethernet(CAT5)

cable up to a distance of 100m (328 ft.) per port.

•115VAC60Hz,3amp(NetWay8).

NetWay16:

•Sixteen(16)portsofcameras/edgedevicesoverethernet(CAT5)

cable up to a distance of 100m (328 ft.) per port.

•115VAC60Hz,4.9amp(NetWay16).

Common Specifications:

Agency Listings:

•UL/CULListedforInformationTechnologyEquipment

 (UL60950-1).

Power:

•Unitprovidesupto30Wmax.fullpowerperport.

Total power: NetWay8 - 150W, NetWay16 - 300W.

•IEEE802.3afandIEEE802.3atcompliant(PoEPlus).

•Shortcircuitprotection.

Functions:

•Autodetectionandprotectionoflegacy

non-PoE cameras/edge devices.

Features (cont’d):

•Illuminatedmasterpowerdisconnectcircuitbreaker

with manual reset (switch).

•IndividualportstatusLEDs.

•IEC320-3-wiregroundedlinecord(detachable).

•Unitcanberackorshelfmounted.

•1UrackmountchassisforuseinstandardEIA19”rack.

Accessories:

NetWay1512:

•15Wadapterfornon-PoEcompliantIPcameras.

NetWay3012:

•25Wadapterfornon-PoEcompliantIP

fixed or PTZ cameras.

NetWayXT:

•PoErepeatermoduleextendsrange100m(328ft.).

Installation Instructions:

NetWay is not intended to be connected to outside plant leads.

1. AttachmountingbracketstoNetWayunitforrackorwallmountinstallation(Figs. 7 or 8, pg. 10).

Affix rubber pads to NetWay for shelf installation (Fig. 9, pg. 10).

2. Securetheunitinarackorplaceunitonashelfasdesired.

Note:Thefollowingfactorsshouldbetakenintoconsiderationwheninstallingtheserackmountunits:

 a.Theunitistobeinstalledinaspacewherethemaximumambienttemperaturedoesnotexceed104ºF(40ºC).

 b.Takecaretoinsurethereissufficientairflowaroundtheunitandthatobstructionsdonotimpedeit.

 c.Whenmountingunitsinrack,takecaretoavoidunevenloadingwhichcancauseahazardouscondition.

3. Setilluminatedmasterpowerdisconnectcircuitbreakertothe(OFF)position(Fig. 1d, pg. 3).

4. PlugthegroundedAClinecord(included)intotheIEC320connectoroftheNetWayunit

(Fig. 1e, pg. 3).Plugunitintoareliableearthgroundedsocket.Whenusingmultipleunitsthesumoftheindividual

name plate ratings should not exceed the supply circuit rating.

5. Connectstructuredcablesfromportmarked[IN]onNetWaytothecorrespondinginputsofanethernetswitchor

video server (Fig. 1b, pg. 3, Fig. 4, pg. 5).

6. Connectstructuredcablesfromportmarked[OUT]onNetWaytoPoEcompliantcamera/edge

devices (Fig. 1a, pg. 3, Fig. 4, pg. 5).

7. UponcompletionofwiringsetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)

position (Fig. 1d, pg. 3).

8. PortstatusLEDsontheNetWaywillinitializewhenPoEdevicesareconnectedasfollows:

 - LEDwillilluminatewhendevicesareIEEE802.3afcompliant.

 - LEDwillblinkonceandilluminatewhendevicesareIEEE802.3atcompliant(PoEPlus).

1 2 3 4 5 6 7 8

Komentáře k této Příručce

Žádné komentáře

Altronix NetWay8 Installation Instructions Uživatelský manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Příslušenství pro elektriku Altronix NetWay8 Installation Instructions